ioplazy.blogg.se

1. #COMPUTRAINER USB DRIVER INSTALL#
2. #COMPUTRAINER USB DRIVER SERIAL#
3. #COMPUTRAINER USB DRIVER UPGRADE#
4. #COMPUTRAINER USB DRIVER ANDROID#
5. #COMPUTRAINER USB DRIVER SOFTWARE#

#COMPUTRAINER USB DRIVER SERIAL#

To see all of the serial devices connected. On OSX, it's a little trickier to figure out what port the Computrainer is on. For example, if it's on comm port 3 you'd change the line above to this: ctport="com3"

#COMPUTRAINER USB DRIVER SOFTWARE#

On Windows, you should be able to find this in other Computrainer software or Device Manager under "Ports". In the config.txt file with your port number. If this isn't working for you, find the port that your Computrainer is connected to and replace ctport="auto" On Windows we search com1- com24 and on Mac we search all of the com ports (/dev/cu.*). Be sure to save the file and restart TrainerRoad for changes to take effect.

If you try to pair the device and it fails, you'll see a dropdown menu in Windows to choose the port.Īlternatively, there is a config.txt file in your Documents folder under the TrainerRoad subfolder. The Computrainer will still use its power measurements internally to set the load on the trainer in ERG mode. For example, if you have a Quarq power meter and a Computrainer paired at the same time, cadence and power will be recorded from the Quarq and speed will be recorded from your Computrainer. For cadence, speed, and power, any device that sends this data will be shown and recorded instead of the Computrainer data. If you have ANT+ or Bluetooth Smart devices paired in addition to your Computrainer, you'll see this data as well.

Use the up/down arrows to adjust the slope setting in 0.1 increments. You can also use F2 (or the mode dropdown on the devices tab) to switch to Slope mode. You can use the up and down arrows to adjust this by 5-watt increments. Since there is no watt target in a free ride, you'll automatically start at 150W. Since the goal of the test interval is to put out the highest average watts possible, you'll want to shift and/or adjust the slope up or down so you can pedal at your optimal cadence. Test Workoutsĭuring test intervals of the test workouts (8-minute test and 20-minute test), TrainerRoad will automatically switch to Slope mode at 2%. Tighten to make the number go up, and loosen to make the number go down. If the number is outside the range of 2.5 to 3.5 you may want to adjust the tension on the rear wheel. After the spindown, the new number will show up on top. The old number shows on the bottom and 0.00 shows up on top. This will pause the workout and allow you to spin up and coast down to get a new calibration number. You can also use the play/pause button on the workout screen CalibrationĪfter the trainer is warmed up (5-10 minutes), it's good practice to calibrate the CompuTrainer. Press Start on the handlebar unit to start or stop a workout. Note: These adapters are out of stock at RacerMate, but you can find an alternative cable that we have tested here.ĬompuTrainer: General Use with TrainerRoad Starting and stopping a workout To use your CompuTrainer with TrainerRoad, you need a USB to Stereo adapter. +/- buttons - In Slope mode - changes the slope up or down by 0.1 In Erg mode - changes the workout percent up or down, which increases or decreases the target watts Adapter Once the new calibration value is displayed, press F3 to save the new value and resume the workout Once in calibration mode, spin up to the required speed on the handlebar unit and then coast. You can find that forum from the following link: CompuTrainer Forum Buttonsį2 - Switches modes between Slope (gradient) and ERG (resistance changes to match target power)į3 - Enter or exit calibration mode.

#COMPUTRAINER USB DRIVER UPGRADE#

We are not aware if any other means to upgrade the handlebar unit are available.įor details on further support, we suggest checking with fellow CompuTrainer owners by posting on The RacerMate Forum. The documentation to upgrade the CompuTrainer forwards you to the same page stating they are closed. Note: Racermate's website now claims they are officially closed. If it is older it may just work but if it doesn't, you'll need an upgrade from RacerMate. This is the number that shows up on the screen when the unit is powered on. The handlebar unit should have firmware version 43.45 or newer.

#COMPUTRAINER USB DRIVER INSTALL#

#COMPUTRAINER USB DRIVER ANDROID#

CompuTrainer support is not available for iOS or Android devices. The CompuTrainer will work with TrainerRoad through the "Legacy" Windows and Mac apps.